-- CISCO-IGMP-SNOOPING-MIB: MIB for IGMP Snooping Configuration.
--   
-- May 2002, Binh P Le
--   
-- Copyright (c) 2002, -2008 by Cisco Systems Inc.
--   

-- All rights reserved.
-- ***************************************************************

CISCO-IGMP-SNOOPING-MIB DEFINITIONS ::= BEGIN

IMPORTS
    OBJECT-TYPE,
    MODULE-IDENTITY,
    Counter32,
    Unsigned32,
    Integer32
        FROM SNMPv2-SMI
    MODULE-COMPLIANCE,
    OBJECT-GROUP
        FROM SNMPv2-CONF
    TruthValue,
    TimeStamp,
    TEXTUAL-CONVENTION,
    RowStatus
        FROM SNMPv2-TC
    ifIndex,
    InterfaceIndex
        FROM IF-MIB
    InetAddressType,
    InetAddress
        FROM INET-ADDRESS-MIB
    VlanIndex
        FROM CISCO-VTP-MIB
    CiscoPortList
        FROM CISCO-TC
    Percent
        FROM CISCO-QOS-PIB-MIB
    ciscoMgmt
        FROM CISCO-SMI;


ciscoIgmpSnoopingMIB MODULE-IDENTITY
    LAST-UPDATED    "200711080000Z"
    ORGANIZATION    "Cisco System, Inc."
    CONTACT-INFO
            "Cisco Systems
            Customer Service

            Postal: 170 W Tasman Drive
            San Jose, CA  95134
            USA

            Tel: +1 800 553-NETS

            E-mail: cs-lan-switch-snmp@cisco.com, cs-ipmulticast@cisco.com"
    DESCRIPTION
        "The MIB module for IGMP Snooping feature.

        Internet Group Management Protocol (IGMP) is the protocol used 
        by IPv4 end hosts to indicate their interest in receiving 
        multicast traffic for certain multicast groups to neighboring 
        multicast routers. Version 3 of IGMP adds support for source 
        based filtering; which means the end hosts can specifically 
        indicate to receive or not-receive multicast packets from 
        specific source addresses. This information is used by the 
        multicast routers to restrict forwarding of multicast traffic 
        for the host.

        IGMP Snooping is a switch protocol. A switch that implements 
        IGMP Snooping listens to the IGMP messages exchanged between 
        the hosts and router, then provides selective transmission of 
        multicast traffic based on multicast mac destination address
        or multicast group address.  With IGMPv3 support, 
        IGMP Snooping can potentially provide selective transmission
        of multicast data based on (source address, group address) 
        onto the ports that are interested. In addition to this, 
        IGMP Snooping can also provide proxy reporting, report 
        suppression and fast leave capabilities."
    REVISION        "200711080000Z"
    DESCRIPTION
        "Added value 'unknown(4)' to CisIgmpVersion.

        Added support for the following:
        - cisL2EntryLimitGroup
        - cisTrackingLimitGroup
        - cisSourceOnlyLimitGroup
        - cisRateLimitGroup2
        - cisVlanConfigGroup2
        - cisSourceOnlyAgeTimerInSecGroup.

        Deprecated cisRateLimitGroup,
        cisGlobalSourceOnlyLearnGroup."
    REVISION        "200404020000Z"
    DESCRIPTION
        "Replaced the import of PortList from Q-BRIDGE-MIB with
        CiscoPortList from CISCO-TC."
    REVISION        "200303240000Z"
    DESCRIPTION
        "Add support for the following:
        - per VLAN IGMP Snooping configuration and group
          membership information
        - per port IGMP Snooping configuration
        - per VLAN IGMP Querier configuration
        - global rate-limit control objects
        - extend the cisSystemInfo to include more IGMP Snooping
          configuration related objects."
    REVISION        "200205050000Z"
    DESCRIPTION
        "Initial version of this MIB module."
    ::= { ciscoMgmt 263 }



-- Textual Conventions

CisIgmpMode ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
        "A value that represents a working mode of IGMP protocol in a
        device.

        auto(1)    : The system decides the working mode by itself.

        igmpOnly(2): Working on IGMP mode only.

        igmpCgmp(3): Working on both IGMP and CGMP modes."
    SYNTAX          INTEGER  {
                        auto(1),
                        igmpOnly(2),
                        igmpCgmp(3)
                    }

CisIgmpVersion ::= TEXTUAL-CONVENTION
    STATUS          current
    DESCRIPTION
        "A value that represents the version of IGMP:

        version1(1)     : Version 1 of IGMP
        version2(2)     : Version 2 of IGMP
        version3(3)     : Version 3 of IGMP
        unknown(4)      : Version of IGMP is not determined."
    SYNTAX          INTEGER  {
                        version1(1),
                        version2(2),
                        version3(3),
                        unknown(4)
                    }
ciscoIgmpSnoopingNotification  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIB 0 }

ciscoIgmpSnoopingMIBObject  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIB 1 }

cisSystemInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 1 }

cisStatisticsInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 2 }

cisRateLimitInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 3 }

cisVlanConfigInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 4 }

cisIfConfigInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 5 }

cisMulticastRouterInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 6 }

cisMulticastGroupInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 7 }

cisResourceLimitInfo  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIBObject 8 }


-- ------------------------------------------------------------
-- - The cisSystemInfo group.
-- ------------------------------------------------------------

cisIgmpSnoopingEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object indicates whether IGMP Snooping has been
        enabled for the system." 
    ::= { cisSystemInfo 1 }

cisV3ProcessEnabledAdminStatus OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object indicates the administrative status of IGMP v3
        processing in the system. With the condition that IGMP
        protocol has been enabled, a system will process IGMPv3 
        messages if this object is set to 'true', or it will process
        only IGMPv1/v2 messages if this object is set to 'false'." 
    ::= { cisSystemInfo 2 }

cisV3ProcessEnabledOperStatus OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the current operational status of IGMP
        v3 processing in the system. This object is enabled if the 
        system is operating with IGMPv3 protocol. Value of this object
        will be set to 'true' if the system is operating in IGMP v3,
        and 'false' if it is operating in IGMPv1/v2." 
    ::= { cisSystemInfo 3 }

cisFastLeaveEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object indicates whether Fast-Leave mechanism has been
        configured to be enabled in the system. If Fast-Leave is 
        enabled in the switch, IGMP Snooping will prune the port on 
        which an IGMP leave message has been received without waiting 
        for the Group Specific Query to timeout to determine whether 
        there are any more hosts on that port for that group. If 
        the value of cisV3ProcessEnabledOperStatus is 'false',
        this object will not have any effect." 
    ::= { cisSystemInfo 4 }

cisFastBlockEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The object indicates whether Fast-Block mechanism has been
        enabled for the system. This object only has effect if the
        value of cisV3ProcessEnabledOperStatus is 'true'." 
    ::= { cisSystemInfo 5 }

cisAdminMode OBJECT-TYPE
    SYNTAX          CisIgmpMode
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The object indicates the administrative snooping mode of IGMP
        Snooping feature, depends on whether only IGMP devices, or
        also CGMP devices are existing in the network." 
    ::= { cisSystemInfo 6 }

cisOperMode OBJECT-TYPE
    SYNTAX          CisIgmpMode
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the operational snooping mode of the
        device. The object should return igmpOnly(2) or igmpCgmp(3)
        only. Value of this object is meaningful only if the value
        of cisIgmpSnoopingEnabled is 'true'." 
    ::= { cisSystemInfo 7 }

cisLeaveQueryType OBJECT-TYPE
    SYNTAX          INTEGER  {
                        generalQuery(1),
                        macGenQuery(2),
                        auto(3)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The object indicates the type of IGMP-leave query that the
        device will send on the interface the IGMP-leave message was
        received.

        generalQuery(1)  : A General Query will be sent to all hosts
                         connecting to that interface.

        macGenQuery(2)   : A MAC-Based General Query will be sent to all
                         hosts in multicast groups that are associated
                         with the MAC-level address. MAC-Based General
                         Query is not a standard, it is a part of CGMP
                         (Cisco Group Management Protocol).

        auto(3)          : A Group-Specific query will be sent if there
                         are no IGMPv1 hosts detected in the network.
                         Otherwise a MAC-Based General Query will be 
                         sent." 
    ::= { cisSystemInfo 8 }

cisAddressAliasingMode OBJECT-TYPE
    SYNTAX          INTEGER  {
                        normal(1),
                        fallback(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the current IGMP Address Aliasing Mode of
        the device.

        normal(1)  : IGMP is working in normal mode without detecting
                   address aliasing.
        fallback(2): address aliasing is detected. The device stops
                   listening to the multicast control traffic and stays
                   in the fallback mode for an expiry time before 
                   getting back to the normal mode." 
    ::= { cisSystemInfo 9 }

cisFallbackTime OBJECT-TYPE
    SYNTAX          TimeStamp
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the time the IGMP address aliasing mode
        is fallback(2)." 
    ::= { cisSystemInfo 10 }

cisReportSuppressionEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "When this object is set to 'true', IGMP Snooping will
        suppress duplicate IGMP Reports.  When this object is set 
        to 'false', all IGMP Reports are forwarded to all multicast
        routers in the VLAN." 
    ::= { cisSystemInfo 11 }

cisTopoChangeFloodQueryCount OBJECT-TYPE
    SYNTAX          Unsigned32 (1..10)
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies the flooding period for multicast
        traffic upon receiving Topology Change Notifications (TCN).  
        IGMP Snooping will flood multicast traffic until
        cisTopoChangeFloodQueryCount number of IGMP General Queries
        are received by IGMP Snooping." 
    ::= { cisSystemInfo 12 }

cisTopoChangeQuerySolicitEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies whether the device running IGMP
        Snooping will solicit IGMP General Queries from the 
        Querier upon receiving a Topology Change Notification (TCN).
        The root device will always solicit IGMP General Queries 
        on TCN irrespective of the value of 
        cisTopoChangeQuerySolicitEnabled." 
    ::= { cisSystemInfo 13 }

cisSourceOnlyLearningEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies whether Source Only multicast entries
        are learned by IGMP Snooping or not." 
    ::= { cisSystemInfo 14 }

cisSourceOnlyEntryAgeTime OBJECT-TYPE
    SYNTAX          Integer32 (0..2880)
    UNITS           "minutes"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "This object specifies the aging time for Source Only
        multicast entries when cisSourceOnlyLearningEnabled is
        set to 'true'. When cisSourceOnlyEntryAgeTime is set to
        0, aging is disabled. This object is deprecated and
        replaced by 'cisSourceOnlyEntryAgingTime'." 
    ::= { cisSystemInfo 15 }

cisV3SnoopingSupport OBJECT-TYPE
    SYNTAX          INTEGER  {
                        basic(1),
                        full(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates IGMP Snooping support for
        IGMPv3 as described below:
        basic(1): Basic support for IGMPv3. IGMPv3 packets are 
                  processed similar to IGMPv2 packets.  In other words
                  Source list information is not used.  Although this
                  does not break multicast traffic to IGMPv3 hosts,
                  it does not provide any other benefits such as Fast
                  Leave for IGMPv3 hosts, Explicit Host Tracking and
                  Source based filtering.
        full(2):  Full support for IGMPv3.  Provides full IGMPv3 
                  Snooping support.  This includes processing of
                  IGMPv3 source list information along with group
                  information.  Provides support for features such
                  as Fast Leave, Explicit Host Tracking and Proxy
                  Reporting and a potential to do Source based 
                  filtering.
        The value of this object is valid only when 
        cisV3ProcessEnabledAdminStatus is set to 'true'." 
    ::= { cisSystemInfo 16 }

cisSourceOnlyEntryAgingTime OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "seconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies the aging time in seconds for Source
        Only multicast entries when cisSourceOnlyLearningEnabled is
        set to 'true'. When cisSourceOnlyEntryAgingTime is set to
        0, aging is disabled." 
    ::= { cisSystemInfo 17 }
-- ----------------------------------------
-- - The cisStatisticsInfo group.
-- ----------------------------------------

cisInterfaceStatsTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisInterfaceStatsEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table contains statistics information for IGMP Snooping. An
        entry appears in this table for each IGMP Snooping capable 
        interface in the device."
    ::= { cisStatisticsInfo 1 }

cisInterfaceStatsEntry OBJECT-TYPE
    SYNTAX          CisInterfaceStatsEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry contains statistics information for a specific IGMP
        Snooping capable interface. It provides information about
        IGMP messages and reports that have been transmitted and
        received at the interface."
    INDEX           { ifIndex } 
    ::= { cisInterfaceStatsTable 1 }

CisInterfaceStatsEntry ::= SEQUENCE {
        cisTxGeneralQueries       Counter32,
        cisTxGroupSpecificQueries Counter32,
        cisTxReports              Counter32,
        cisTxLeaves               Counter32,
        cisRxGeneralQueries       Counter32,
        cisRxGroupSpecificQueries Counter32,
        cisRxReports              Counter32,
        cisRxLeaves               Counter32,
        cisRxValidPackets         Counter32,
        cisRxInvalidPackets       Counter32,
        cisRxOtherPackets         Counter32,
        cisRxMACGeneralQueries    Counter32,
        cisRxTopoNotifications    Counter32,
        cisV3Allows               Counter32,
        cisV3Blocks               Counter32,
        cisV3IsIncluded           Counter32,
        cisV3IsExcluded           Counter32,
        cisV3ToIncluded           Counter32,
        cisV3ToExcluded           Counter32
}

cisTxGeneralQueries OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP General Queries that have been transmitted through
        an interface." 
    ::= { cisInterfaceStatsEntry 1 }

cisTxGroupSpecificQueries OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Group-Specific Queries that have been transmitted
        through an interface." 
    ::= { cisInterfaceStatsEntry 2 }

cisTxReports OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Membership Reports that have been transmitted
        through an interface." 
    ::= { cisInterfaceStatsEntry 3 }

cisTxLeaves OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Leave messages that have been transmitted through
        an interface." 
    ::= { cisInterfaceStatsEntry 4 }

cisRxGeneralQueries OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP General Queries that have been received at an
        interface." 
    ::= { cisInterfaceStatsEntry 5 }

cisRxGroupSpecificQueries OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Group-Specific Queries that have been received at
        an interface." 
    ::= { cisInterfaceStatsEntry 6 }

cisRxReports OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Membership Reports that have been received at an
        interface." 
    ::= { cisInterfaceStatsEntry 7 }

cisRxLeaves OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total IGMP Leave messages that have been received at an
        interface." 
    ::= { cisInterfaceStatsEntry 8 }

cisRxValidPackets OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total valid IGMP packets have been received at an interface." 
    ::= { cisInterfaceStatsEntry 9 }

cisRxInvalidPackets OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total packets those are not valid IGMP messages received
        at an interface." 
    ::= { cisInterfaceStatsEntry 10 }

cisRxOtherPackets OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total non IGMP messages messages that have been received
        at an interface, comprising cgmp join, pim hello, dvmrp 
        and mospf messages." 
    ::= { cisInterfaceStatsEntry 11 }

cisRxMACGeneralQueries OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total MAC-based General Queries that have been received at
        an interface." 
    ::= { cisInterfaceStatsEntry 12 }

cisRxTopoNotifications OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Total Topology Change Notifications that have been received
        at an interface." 
    ::= { cisInterfaceStatsEntry 13 }

cisV3Allows OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Source-List-Change records with the record type
        ALLOW_NEW_SOURCES that have been sent from hosts connected 
        to an interface. This record type indicates that the Source
        Address fields in this Group Record contain a list of 
        additional sources that the system wishes to hear from, for
        packets sent to the specified multicast address." 
    ::= { cisInterfaceStatsEntry 14 }

cisV3Blocks OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Source-List-Change records with the record type
        BLOCK_OLD_SOURCE that have been sent from hosts connected to
        an interface. This record type indicates that the Source
        Address fields in this Group Record contain a list of the 
        sources that the system no longer wishes to hear from, for 
        packets sent to the specified multicast address." 
    ::= { cisInterfaceStatsEntry 15 }

cisV3IsIncluded OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Current-State records with the state MODE_IS_INCLUDE
        that have been sent from hosts in response to a Query received
        at an interface. This state indicates that the interface has a 
        filter mode of INCLUDE for the specified multicast address." 
    ::= { cisInterfaceStatsEntry 16 }

cisV3IsExcluded OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Current-State records with the state MODE_IS_EXCLUDE
        that have been sent from hosts in response to a Query received
        at an interfaces. This state indicates that the interface has a
        filter mode of EXCLUDE for the specified multicast address." 
    ::= { cisInterfaceStatsEntry 17 }

cisV3ToIncluded OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Filter-Mode-Change records with the record type
        CHANGE_TO_INCLUDE_MODE that have been sent through an 
        interface. This type of record indicates that the filter mode
        has been changed to INCLUDE mode for the specified multicast 
        address, and the Source Address fields in this Group Record 
        will contain the new source list for the specified multicast
        address, if it is not empty." 
    ::= { cisInterfaceStatsEntry 18 }

cisV3ToExcluded OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "Number of Filter-Mode-Change records with the record type
        CHANGE_TO_EXCLUDE_MODE that have been sent through an 
        interface. This type of record indicates that the filter mode
        has been changed to EXCLUDE mode for the specified multicast
        address, and the Source Address fields in this Group Record
        will contain the new source list for the specified multicast
        address, if it is not empty." 
    ::= { cisInterfaceStatsEntry 19 }
 


-- ----------------------------------------
-- The cisRateLimitInfo group.
-- ----------------------------------------

cisGeneralQueryRateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per 30 seconds"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Rate limit for General-Query packets per 30 seconds from
        a control plane address. If the packets exceed the rate,
        snooping will be stalled for a period of 30 seconds." 
    ::= { cisRateLimitInfo 1 }

cisDvmrpRateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per 30 seconds"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Rate limit for DVMRP packets per 30 seconds from
        a control plane address. If the packets exceed the rate,
        snooping will be stalled for a period of 30 second." 
    ::= { cisRateLimitInfo 2 }

cisMospf1RateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per 30 seconds"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Rate limit for MOSPF1 packets per 30 seconds from
        a control plane address. If the packets exceed the rate,
        snooping will be stalled for a period of 30 second." 
    ::= { cisRateLimitInfo 3 }

cisMospf2RateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per 30 seconds"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Rate limit for MOSPF2 packets per 30 seconds from
        a control plane address. If the packets exceed the rate,
        snooping will be stalled for a period of 30 second." 
    ::= { cisRateLimitInfo 4 }

cisPimV2RateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per 30 seconds"
    MAX-ACCESS      read-write
    STATUS          deprecated
    DESCRIPTION
        "Rate limit for PIMv2 packets per 30 seconds from
        a control plane address. If the packets exceed the rate,
        snooping will be stalled for a period of 30 second." 
    ::= { cisRateLimitInfo 5 }

cisRateLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "packets per second"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Rate limit for incoming IGMP messages in packets per seconds,
        applied to each VLAN in the system. IGMP Snooping will be
        disabled on the corresponding VLAN if IGMP message incoming
        rate exceeds the limit, then enabled back automatically once
        IGMP join message rate is below the limit indicated by the
        corresponding instance value of this object. Setting value
        zero to this object means no limitation on IGMP incoming
        message rate." 
    ::= { cisRateLimitInfo 6 }
-- ----------------------------------------
-- - The cisVlanConfigInfo group.
-- ----------------------------------------

cisVlanConfigTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisVlanConfigEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table contains VLAN based configuration information
        for IGMP Snooping."
    ::= { cisVlanConfigInfo 1 }

cisVlanConfigEntry OBJECT-TYPE
    SYNTAX          CisVlanConfigEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is created for each active VLAN in the device
        and deleted when the VLAN becomes inactive."
    INDEX           { cisVlanIndex } 
    ::= { cisVlanConfigTable 1 }

CisVlanConfigEntry ::= SEQUENCE {
        cisVlanIndex                    VlanIndex,
        cisVlanIgmpSnoopingEnabled      TruthValue,
        cisVlanFastLeaveEnabled         TruthValue,
        cisVlanIgmpSnoopingOperMode     CisIgmpMode,
        cisVlanIgmpSnoopingLearningMode INTEGER,
        cisVlanReportSuppressionEnabled TruthValue,
        cisVlanLeaveQueryInterval       Unsigned32
}

cisVlanIndex OBJECT-TYPE
    SYNTAX          VlanIndex
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object indicates the VLAN in which IGMP Snooping
        is configured." 
    ::= { cisVlanConfigEntry 1 }

cisVlanIgmpSnoopingEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "When this object is set to 'true' IGMP Snooping
        is enabled on this VLAN else disabled." 
    ::= { cisVlanConfigEntry 2 }

cisVlanFastLeaveEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies whether Fast-Leave mechanism
        (also known as Immediate-Leave) is to be performed by IGMP
        Snooping or not.  When enabled, IGMP Snooping will remove
        the interface from the group mentioned in the IGMP Leave
        message received on that interface without waiting for the
        IGMP Group-Specific Query to timeout to determine whether 
        there are any more hosts on that interface for that group." 
    ::= { cisVlanConfigEntry 3 }

cisVlanIgmpSnoopingOperMode OBJECT-TYPE
    SYNTAX          CisIgmpMode
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the operational mode of IGMP Snooping.
        The object should return igmpOnly(2) or igmpCgmp(3) only." 
    ::= { cisVlanConfigEntry 4 }

cisVlanIgmpSnoopingLearningMode OBJECT-TYPE
    SYNTAX          INTEGER  {
                        pimDvmrp(1),
                        cgmp(2)
                    }
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies the multicast router port learning
        method for IGMP Snooping as described below:
        pimDvmrp(1) : Protocol Independent Multicast / Distance Vector
                       Multicast Routing Protocol.
        cgmp(2)      : Cisco Group Management Protocol." 
    ::= { cisVlanConfigEntry 5 }

cisVlanReportSuppressionEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This object specifies whether Report Suppression is enabled
        for this VLAN." 
    ::= { cisVlanConfigEntry 6 }

cisVlanLeaveQueryInterval OBJECT-TYPE
    SYNTAX          Unsigned32
    UNITS           "milliseconds"
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "This objects specifies the IGMP leave timer on the VLAN
        interface." 
    ::= { cisVlanConfigEntry 7 }
 


cisIgmpQuerierTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisIgmpQuerierEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table containing information regarding the IGMP Querier in
        the VLAN.  The device can be configured to be the IGMP Querier
        for the VLAN. An IGMP Querier for the VLAN is selected by 
        using a Querier Election process."
    ::= { cisVlanConfigInfo 2 }

cisIgmpQuerierEntry OBJECT-TYPE
    SYNTAX          CisIgmpQuerierEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is created for each active VLAN in the device and
        contains IGMP Querier configuration information related to
        IGMP Snooping for that VLAN. An entry is deleted when the 
        VLAN becomes inactive."
    INDEX           { cisIgmpQuerierVlanIndex } 
    ::= { cisIgmpQuerierTable 1 }

CisIgmpQuerierEntry ::= SEQUENCE {
        cisIgmpQuerierVlanIndex   VlanIndex,
        cisIgmpQuerierEnabled     TruthValue,
        cisIgmpQuerierState       INTEGER,
        cisIgmpQuerierVersion     CisIgmpVersion,
        cisIgmpQuerierAddressType InetAddressType,
        cisIgmpQuerierAddress     InetAddress,
        cisIgmpQuerierInterface   InterfaceIndex
}

cisIgmpQuerierVlanIndex OBJECT-TYPE
    SYNTAX          VlanIndex
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "The object indicates the VLAN that the Querier will send
        IGMP queries on." 
    ::= { cisIgmpQuerierEntry 1 }

cisIgmpQuerierEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "The object indicates whether the device will participate in
        the IGMP Querier election in a VLAN. If the object is set
        to 'true', the device will participate to an election
        process to be a Querier. If the object is set to 'false'
        while the device is acting as the Querier in a VLAN, a new
        election will be activated to choose a different Querier." 
    ::= { cisIgmpQuerierEntry 2 }

cisIgmpQuerierState OBJECT-TYPE
    SYNTAX          INTEGER  {
                        disabled(1),
                        electing(2),
                        querier(3),
                        nonQuerier(4),
                        inactive(5)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the current state of the device as an
        IGMP Querier in a VLAN.

        disabled(1)  : Querier function is disabled for this device
                       in this VLAN.
        electing(2)  : The device is in the election process of the
                       Querier.
        querier(3)   : The device is the current Querier in this 
                       VLAN.
        nonQuerier(4): The device has lost the election process of
                       the Querier.
        inactive(5)  : VLAN is inactive or not an Ethernet VLAN." 
    ::= { cisIgmpQuerierEntry 3 }

cisIgmpQuerierVersion OBJECT-TYPE
    SYNTAX          CisIgmpVersion
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates IGMP version of the Querier for the VLAN.
        IGMP version of the Querier is determined by the type of IGMP
        General Query received by the device."
    REFERENCE       "RFC 3376" 
    ::= { cisIgmpQuerierEntry 4 }

cisIgmpQuerierAddressType OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates IP address type of the IGMP Querier
        for the VLAN." 
    ::= { cisIgmpQuerierEntry 5 }

cisIgmpQuerierAddress OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates IP address of the IGMP Querier
        for the VLAN." 
    ::= { cisIgmpQuerierEntry 6 }

cisIgmpQuerierInterface OBJECT-TYPE
    SYNTAX          InterfaceIndex
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "The object indicates the interface on which IGMP Querier is
        detected for the VLAN.  The value of this object is zero
        if the device itself is acting as IGMP Querier for the VLAN." 
    ::= { cisIgmpQuerierEntry 7 }
 

-- ----------------------------------------
-- - The cisIfConfigInfo group.
-- ----------------------------------------

cisIfConfigTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisIfConfigEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table containing configuration information for IGMP
        Snooping on a layer two interface."
    ::= { cisIfConfigInfo 1 }

cisIfConfigEntry OBJECT-TYPE
    SYNTAX          CisIfConfigEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is created for each interface layer two
        interface."
    INDEX           { ifIndex } 
    ::= { cisIfConfigTable 1 }

CisIfConfigEntry ::= SEQUENCE {
        cisIfTopoChangeFloodEnabled TruthValue
}

cisIfTopoChangeFloodEnabled OBJECT-TYPE
    SYNTAX          TruthValue
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "When this object is set to 'true' multicast traffic will be
        flooded on the port for cisTopoChangeFloodQueryCount of Igmp
        General Queries upon receiving a Topology Change 
        Notification (TCN) for the VLAN to which the port belongs." 
    ::= { cisIfConfigEntry 1 }
 

-- ------------------------------------------------------
-- The cisMulticastRouterInfo group.
-- ------------------------------------------------------

cisMcastRouterCfgTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisMcastRouterCfgEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table containing multicast router configuration information
        for IGMP Snooping."
    ::= { cisMulticastRouterInfo 1 }

cisMcastRouterCfgEntry OBJECT-TYPE
    SYNTAX          CisMcastRouterCfgEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is created for each interface in the VLAN that is
        either learned or configured as multicast router port.
        A multicast router port is learned using the method 
        specified by cisVlanIgmpSnoopingLearningMode."
    INDEX           {
                        ifIndex,
                        cisMcastRouterVlanIndex
                    } 
    ::= { cisMcastRouterCfgTable 1 }

CisMcastRouterCfgEntry ::= SEQUENCE {
        cisMcastRouterVlanIndex VlanIndex,
        cisMcastRouterType      INTEGER,
        cisMcastRouterRowStatus RowStatus
}

cisMcastRouterVlanIndex OBJECT-TYPE
    SYNTAX          VlanIndex
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object indicates the VLAN to which the multicast router
        port belongs." 
    ::= { cisMcastRouterCfgEntry 1 }

cisMcastRouterType OBJECT-TYPE
    SYNTAX          INTEGER  {
                        static(1),
                        dynamic(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates if the multicast router port is
        a configured (static) or learned (dynamic) port." 
    ::= { cisMcastRouterCfgEntry 2 }

cisMcastRouterRowStatus OBJECT-TYPE
    SYNTAX          RowStatus
    MAX-ACCESS      read-create
    STATUS          current
    DESCRIPTION
        "This object is a conceptual row entry that allows to add
        or delete entries to or from the cisMcastRouterCfgTable.
        When creating an entry in this table 'createAndGo' method
        is used and the value of this object is set to 'active'.
        Deactivation of an 'active' entry is not allowed. When
        deleting an entry in this table 'destroy' method is
        used." 
    ::= { cisMcastRouterCfgEntry 3 }
 

-- ----------------------------------------
-- The cisMulticastGroupInfo group.
-- ----------------------------------------

cisMcastGroupTable OBJECT-TYPE
    SYNTAX          SEQUENCE OF CisMcastGroupEntry 
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "Table containing multicast group address information for
        IGMP Snooping."
    ::= { cisMulticastGroupInfo 1 }

cisMcastGroupEntry OBJECT-TYPE
    SYNTAX          CisMcastGroupEntry
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "An entry is created by IGMP Snooping for each group learned
        in the VLAN."
    INDEX           {
                        cisMcastGroupVlanIndex,
                        cisMcastGroupAddressType,
                        cisMcastGroupAddress
                    } 
    ::= { cisMcastGroupTable 1 }

CisMcastGroupEntry ::= SEQUENCE {
        cisMcastGroupVlanIndex        VlanIndex,
        cisMcastGroupAddressType      InetAddressType,
        cisMcastGroupAddress          InetAddress,
        cisMcastGroupFilterMode       INTEGER,
        cisMcastGroupIgmpVersion      CisIgmpVersion,
        cisMcastGroupIncludeHostCount Counter32,
        cisMcastGroupExcludeHostCount Counter32,
        cisMcastGroupPortList         CiscoPortList
}

cisMcastGroupVlanIndex OBJECT-TYPE
    SYNTAX          VlanIndex
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object indicates the VLAN in which the group is learned." 
    ::= { cisMcastGroupEntry 1 }

cisMcastGroupAddressType OBJECT-TYPE
    SYNTAX          InetAddressType
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object indicates IP multicast address type learned
        by IGMP Snooping." 
    ::= { cisMcastGroupEntry 2 }

cisMcastGroupAddress OBJECT-TYPE
    SYNTAX          InetAddress
    MAX-ACCESS      not-accessible
    STATUS          current
    DESCRIPTION
        "This object indicates IP multicast address learned by
        IGMP Snooping." 
    ::= { cisMcastGroupEntry 3 }

cisMcastGroupFilterMode OBJECT-TYPE
    SYNTAX          INTEGER  {
                        include(1),
                        exclude(2)
                    }
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates a the IGMP filter mode for the group.

        include(1) : reception of multicast packets sent to the group
                     specified by cisMcastGroupAddress is requested
                     only from the specified IPv4 source addresses
                     listed in the IGMPv3 Membership Reports.
        exclude(2) : reception of multicast packets sent to the group
                     specified by cisMcastGroupAddress is requested
                     from all except from the list of IPv4 source
                     addresses specified in the IGMPv3 Membership
                      Reports.

        The filter mode is determined by the type of Group Record
        received in the IGMP Membership Report received by the 
        device.  Groups for which IGMPv1/v2 Membership Reports 
        are received are considered to have a cisMcastGroupFilterMode
        of 'exclude'."
    REFERENCE       "RFC 3376" 
    ::= { cisMcastGroupEntry 4 }

cisMcastGroupIgmpVersion OBJECT-TYPE
    SYNTAX          CisIgmpVersion
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the IGMP version for the group.
        This is determined by the type of IGMP Membership Report
        received by the device." 
    ::= { cisMcastGroupEntry 5 }

cisMcastGroupIncludeHostCount OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the number of hosts that
        are in INCLUDE mode for the group." 
    ::= { cisMcastGroupEntry 6 }

cisMcastGroupExcludeHostCount OBJECT-TYPE
    SYNTAX          Counter32
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the number of hosts that
        are in EXCLUDE mode for the group." 
    ::= { cisMcastGroupEntry 7 }

cisMcastGroupPortList OBJECT-TYPE
    SYNTAX          CiscoPortList
    MAX-ACCESS      read-only
    STATUS          current
    DESCRIPTION
        "This object indicates the set of ports on which IGMP
        Membership Reports are received for the group indicating
        interest to receive traffic sent to the group." 
    ::= { cisMcastGroupEntry 8 }
 


-- -----------------------------------------
-- cisResourceLimitInfo groups
-- -----------------------------------------

cisL2EntryLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Specifies the maximum number of Layer 2 multicast entries
        that IGMP Snooping can install in the Layer 2 forwarding
        table. For multicast groups not being installed in the 
        Layer 2 forwarding table due to exceeding the limitation,
        their traffic will be flooded within the VLAN." 
    ::= { cisResourceLimitInfo 1 }

cisEntryTrackingLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Specifies the maximum number of entries can be installed
        in the tracking database." 
    ::= { cisResourceLimitInfo 2 }

cisSourceOnlyPercentageScanLimit OBJECT-TYPE
    SYNTAX          Percent
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Specifies the percentage of IGMP Snooping Source Only
        entries to be processed in each Source Only timeout
        period, in which they will be timed out in batches.
        Entries not processed due to this limitation will
        remain in the Layer 2 forwarding table." 
    ::= { cisResourceLimitInfo 3 }

cisSourceOnlyLearningLimit OBJECT-TYPE
    SYNTAX          Unsigned32
    MAX-ACCESS      read-write
    STATUS          current
    DESCRIPTION
        "Specifies the maximum number of Layer 2 multicast Source
        Only entries that IGMP Snooping can install in the Layer 2
        forwarding table. If the number of multicast Source Only
        groups in the system exceeds this limit, snooping entries
        will not be installed for the over-limit groups and Source
        Only traffic for these groups will be flooded within the
        VLAN." 
    ::= { cisResourceLimitInfo 4 }
-- ----------------------------------------
-- Conformance Information
-- ----------------------------------------

cisMIBConformance  OBJECT IDENTIFIER
    ::= { ciscoIgmpSnoopingMIB 2 }

cisMIBCompliances  OBJECT IDENTIFIER
    ::= { cisMIBConformance 1 }

cisMIBGroups  OBJECT IDENTIFIER
    ::= { cisMIBConformance 2 }


-- Compliance statements

cisV2Compliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for device support IGMPv1/v2
        Snooping protocol."
    MODULE          -- this module
    MANDATORY-GROUPS { cisSystemGroup }

    GROUP           cisSystemV2Group
    DESCRIPTION
        "This group is mandatory in systems that support
        global configuration for IGMPv2 Snooping feature."

    GROUP           cisStatsGroup
    DESCRIPTION
        "This group is optional, and should be implemented if the
        system provides statistics information for IGMP Snooping
        protocol version 1 and 2."
    ::= { cisMIBCompliances 1 }

cisV3Compliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for device support IGMPv3 Snooping
        protocol."
    MODULE          -- this module
    MANDATORY-GROUPS { cisSystemGroup }

    GROUP           cisSystemV2Group
    DESCRIPTION
        "This group is mandatory in systems that support global
        configuration for IGMPv2 Snooping feature."

    GROUP           cisSystemV3Group
    DESCRIPTION
        "This group is mandatory in systems that support global
        configuration for IGMPv3 Snooping feature."

    GROUP           cisStatsGroup
    DESCRIPTION
        "This group is optional, and should be implemented if the
        system provides statistics information of IGMP Snooping 
        protocol version 1 and 2."

    GROUP           cisV3StatsGroup
    DESCRIPTION
        "This group is optional, and should be implemented if the
        system provides statistics information of IGMP Snooping
        protocol version 3."
    ::= { cisMIBCompliances 2 }

cisIgmpSnoopingMIBCompliance MODULE-COMPLIANCE
    STATUS          deprecated
    DESCRIPTION
        "The compliance statement for device supporting
        IGMP Snooping.This compliance is deprecated and 
        superceded by cisIgmpSnoopingMIBCompliance2."
    MODULE          -- this module
    MANDATORY-GROUPS { cisBaseConfigGroup }

    GROUP           cisGlobalTcnGroup
    DESCRIPTION
        "This group is mandatory only for the device that
        provides global configuration of Topology Change
        Notification (TCN) related parameters."

    GROUP           cisGlobalSourceOnlyLearnGroup
    DESCRIPTION
        "This group is mandatory only for the device that
        provides global configuration for Source Only 
        learning via IGMP Snooping."

    GROUP           cisGlobalIgmpV3ConfigGroup
    DESCRIPTION
        "This group is mandatory only for the device that
        provides global configuration for IGMPv3 Snooping."

    GROUP           cisGlobalIgmpV3InfoGroup
    DESCRIPTION
        "This group is optional."

    GROUP           cisExtConfig1Group
    DESCRIPTION
        "This group is optional."

    GROUP           cisExtConfig2Group
    DESCRIPTION
        "This group is optional."

    GROUP           cisStatsGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device provides statistics information for IGMP
        Snooping for IGMP version 1 and 2."

    GROUP           cisV3StatsGroup
    DESCRIPTION
        "The group is optional, and should be implemented if
        the device provides statistics information of IGMP 
        Snooping for IGMP version 3."

    GROUP           cisRateLimitGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device provides configuration information of 
        rate-limit controls."

    GROUP           cisVlanConfigGroup
    DESCRIPTION
        "This group is mandatory for devices that support IGMP
        Snooping configuration per VLAN."

    GROUP           cisIgmpQuerierConfigGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device is capable to perform the IGMP Querier 
        functionality."

    GROUP           cisIgmpQuerierInfoGroup
    DESCRIPTION
        "This group is optional."

    GROUP           cisMcastRouterConfigGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device supports Multicast router port management."

    GROUP           cisMcastGroupInfoGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device maintains multicast group information."

    GROUP           cisIfConfigGroup
    DESCRIPTION
        "This group is mandatory only for devices that supports
        IGMP Snooping configuraton on an interface basis."

    OBJECT          cisIgmpQuerierAddressType
    SYNTAX          INTEGER  {
                        ipv4(1)
                    }
    DESCRIPTION
        "Only IPv4 addresses need to be supported."
    ::= { cisMIBCompliances 3 }

cisIgmpSnoopingMIBCompliance2 MODULE-COMPLIANCE
    STATUS          current
    DESCRIPTION
        "The compliance statement for device supporting
        IGMP Snooping."
    MODULE          -- this module
    MANDATORY-GROUPS { cisBaseConfigGroup }

    GROUP           cisGlobalTcnGroup
    DESCRIPTION
        "This group is mandatory only for the device that
        provides global configuration of Topology Change
        Notification (TCN) related parameters."

    GROUP           cisGlobalIgmpV3ConfigGroup
    DESCRIPTION
        "This group is mandatory only for the device that
        provides global configuration for IGMPv3 Snooping."

    GROUP           cisGlobalIgmpV3InfoGroup
    DESCRIPTION
        "This group is optional."

    GROUP           cisExtConfig1Group
    DESCRIPTION
        "This group is optional."

    GROUP           cisExtConfig2Group
    DESCRIPTION
        "This group is optional."

    GROUP           cisStatsGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device provides statistics information for IGMP
        Snooping for IGMP version 1 and 2."

    GROUP           cisV3StatsGroup
    DESCRIPTION
        "The group is optional, and should be implemented if
        the device provides statistics information of IGMP 
        Snooping for IGMP version 3."

    GROUP           cisVlanConfigGroup
    DESCRIPTION
        "This group is mandatory for devices that support IGMP
        Snooping configuration per VLAN."

    GROUP           cisIgmpQuerierConfigGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device is capable to perform the IGMP Querier 
        functionality."

    GROUP           cisIgmpQuerierInfoGroup
    DESCRIPTION
        "This group is optional."

    GROUP           cisMcastRouterConfigGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device supports Multicast router port management."

    GROUP           cisMcastGroupInfoGroup
    DESCRIPTION
        "This group is optional, and should be implemented if
        the device maintains multicast group information."

    GROUP           cisIfConfigGroup
    DESCRIPTION
        "This group is mandatory only for devices that supports
        IGMP Snooping configuraton on an interface basis."

    GROUP           cisL2EntryLimitGroup
    DESCRIPTION
        "This group is mandatory only for devices that supports
        IGMP Snooping configuration for Layer 2 entry limit."

    GROUP           cisTrackingLimitGroup
    DESCRIPTION
        "This group is mandatory only for devices that supports
        configuration for tracking database limitation in IGMP
        Snooping."

    GROUP           cisSourceOnlyLimitGroup
    DESCRIPTION
        "This group is mandatory only for devices that support
        configuration for Source Only entries in IGMP Snooping."

    GROUP           cisRateLimitGroup2
    DESCRIPTION
        "This group is mandatory only for devices that support
        configuration of packet limit rate in IGMP Snooping."

    GROUP           cisVlanConfigGroup2
    DESCRIPTION
        "This group is mandatory only for devices that support
        per VLAN configuration for Leave Query Interval and 
        Report Suppression in IGMP Snooping."

    GROUP           cisSourceOnlyAgeTimerInSecGroup
    DESCRIPTION
        "This group ins mandatory only for devices that support
        Source Only control and age timer in seconds."

    OBJECT          cisIgmpQuerierAddressType
    SYNTAX          INTEGER  {
                        ipv4(1)
                    }
    DESCRIPTION
        "Only IPv4 addresses need to be supported."
    ::= { cisMIBCompliances 4 }

-- Units of Conformance

cisSystemGroup OBJECT-GROUP
    OBJECTS         { cisIgmpSnoopingEnabled }
    STATUS          deprecated
    DESCRIPTION
        "A collection of object(s) providing global system information
        about, and control over, IGMP Snooping protocol operation on
        device."
    ::= { cisMIBGroups 1 }

cisSystemV2Group OBJECT-GROUP
    OBJECTS         { cisFastLeaveEnabled }
    STATUS          deprecated
    DESCRIPTION
        "A collection of additional objects providing global system
        information about, and control over, IGMPv2 Snooping protocol 
        operation on the device."
    ::= { cisMIBGroups 2 }

cisSystemV3Group OBJECT-GROUP
    OBJECTS         {
                        cisV3ProcessEnabledAdminStatus,
                        cisV3ProcessEnabledOperStatus,
                        cisFastBlockEnabled
                    }
    STATUS          deprecated
    DESCRIPTION
        "A collection of additional objects providing global system
        information about, and control over, IGMPv3 Snooping protocol 
        operation on the device."
    ::= { cisMIBGroups 3 }

cisStatsGroup OBJECT-GROUP
    OBJECTS         {
                        cisTxGeneralQueries,
                        cisTxGroupSpecificQueries,
                        cisTxReports,
                        cisTxLeaves,
                        cisRxGeneralQueries,
                        cisRxGroupSpecificQueries,
                        cisRxReports,
                        cisRxLeaves,
                        cisRxValidPackets,
                        cisRxInvalidPackets,
                        cisRxOtherPackets,
                        cisRxMACGeneralQueries,
                        cisRxTopoNotifications
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing statistics
        information of IGMP Snooping version 1 and 2."
    ::= { cisMIBGroups 4 }

cisV3StatsGroup OBJECT-GROUP
    OBJECTS         {
                        cisV3Allows,
                        cisV3Blocks,
                        cisV3IsIncluded,
                        cisV3IsExcluded,
                        cisV3ToIncluded,
                        cisV3ToExcluded
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing additional
        statistics information of IGMPv3 Snooping."
    ::= { cisMIBGroups 5 }

cisBaseConfigGroup OBJECT-GROUP
    OBJECTS         { cisIgmpSnoopingEnabled }
    STATUS          current
    DESCRIPTION
        "A basic collection of object(s) providing IGMP Snooping
        global configuration."
    ::= { cisMIBGroups 6 }

cisGlobalIgmpV3ConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cisV3ProcessEnabledAdminStatus,
                        cisV3ProcessEnabledOperStatus,
                        cisFastBlockEnabled
                    }
    STATUS          current
    DESCRIPTION
        "A collection of global IGMPv3 Snooping related objects."
    ::= { cisMIBGroups 7 }

cisGlobalIgmpV3InfoGroup OBJECT-GROUP
    OBJECTS         { cisV3SnoopingSupport }
    STATUS          current
    DESCRIPTION
        "A collection of global IGMPv3 Snooping related objects."
    ::= { cisMIBGroups 8 }

cisExtConfig1Group OBJECT-GROUP
    OBJECTS         {
                        cisFastLeaveEnabled,
                        cisAdminMode,
                        cisOperMode,
                        cisLeaveQueryType,
                        cisAddressAliasingMode,
                        cisFallbackTime
                    }
    STATUS          current
    DESCRIPTION
        "A miscellaneous collection of object(s) for the device
        that supports global IGMP Snooping configuration."
    ::= { cisMIBGroups 9 }

cisExtConfig2Group OBJECT-GROUP
    OBJECTS         { cisReportSuppressionEnabled }
    STATUS          current
    DESCRIPTION
        "An extended collection of miscellaneous global
        configuration IGMP Snooping objects."
    ::= { cisMIBGroups 10 }

cisGlobalTcnGroup OBJECT-GROUP
    OBJECTS         {
                        cisTopoChangeFloodQueryCount,
                        cisTopoChangeQuerySolicitEnabled
                    }
    STATUS          current
    DESCRIPTION
        "A collection of global Topology Change
        Notification (TCN) related configuration objects."
    ::= { cisMIBGroups 11 }

cisGlobalSourceOnlyLearnGroup OBJECT-GROUP
    OBJECTS         {
                        cisSourceOnlyLearningEnabled,
                        cisSourceOnlyEntryAgeTime
                    }
    STATUS          deprecated
    DESCRIPTION
        "A collection of global Source Only entry learning
        objects."
    ::= { cisMIBGroups 12 }

cisRateLimitGroup OBJECT-GROUP
    OBJECTS         {
                        cisGeneralQueryRateLimit,
                        cisDvmrpRateLimit,
                        cisMospf1RateLimit,
                        cisMospf2RateLimit,
                        cisPimV2RateLimit
                    }
    STATUS          deprecated
    DESCRIPTION
        "A collection of object(s) providing rate-limit information
        of protocol packets handling in IGMP Snooping."
    ::= { cisMIBGroups 13 }

cisVlanConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cisVlanIgmpSnoopingEnabled,
                        cisVlanFastLeaveEnabled,
                        cisVlanIgmpSnoopingOperMode,
                        cisVlanIgmpSnoopingLearningMode
                    }
    STATUS          current
    DESCRIPTION
        "A collectin of objects for VLAN configuration of
        IGMP Snooping."
    ::= { cisMIBGroups 14 }

cisIgmpQuerierConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cisIgmpQuerierEnabled,
                        cisIgmpQuerierState
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) for IGMP Querier configuration
        of IGMP Snooping."
    ::= { cisMIBGroups 15 }

cisIgmpQuerierInfoGroup OBJECT-GROUP
    OBJECTS         {
                        cisIgmpQuerierVersion,
                        cisIgmpQuerierAddressType,
                        cisIgmpQuerierAddress,
                        cisIgmpQuerierInterface
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) for IGMP Querier information."
    ::= { cisMIBGroups 16 }

cisMcastRouterConfigGroup OBJECT-GROUP
    OBJECTS         {
                        cisMcastRouterType,
                        cisMcastRouterRowStatus
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing multicast
        router port information."
    ::= { cisMIBGroups 17 }

cisMcastGroupInfoGroup OBJECT-GROUP
    OBJECTS         {
                        cisMcastGroupFilterMode,
                        cisMcastGroupIgmpVersion,
                        cisMcastGroupIncludeHostCount,
                        cisMcastGroupExcludeHostCount,
                        cisMcastGroupPortList
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing multicast
        group information."
    ::= { cisMIBGroups 18 }

cisIfConfigGroup OBJECT-GROUP
    OBJECTS         { cisIfTopoChangeFloodEnabled }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing IGMP Snoop
        configuration on an interface."
    ::= { cisMIBGroups 19 }

cisL2EntryLimitGroup OBJECT-GROUP
    OBJECTS         { cisL2EntryLimit }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing Layer 2 multicast
        entries limit configuration and information in
        IGMP Snooping."
    ::= { cisMIBGroups 20 }

cisTrackingLimitGroup OBJECT-GROUP
    OBJECTS         { cisEntryTrackingLimit }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing configuration and
        information of tracking database limitation in IGMP
        Snooping."
    ::= { cisMIBGroups 21 }

cisSourceOnlyLimitGroup OBJECT-GROUP
    OBJECTS         {
                        cisSourceOnlyPercentageScanLimit,
                        cisSourceOnlyLearningLimit
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing Source Only learning
        limit configuration and information in IGMP Snooping."
    ::= { cisMIBGroups 22 }

cisRateLimitGroup2 OBJECT-GROUP
    OBJECTS         { cisRateLimit }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing additional rate-limit
        information of protocol packets handling in IGMP Snooping."
    ::= { cisMIBGroups 23 }

cisVlanConfigGroup2 OBJECT-GROUP
    OBJECTS         {
                        cisVlanReportSuppressionEnabled,
                        cisVlanLeaveQueryInterval
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing per VLAN configuration
        of Report Suppression and Leave Query Interval for IGMP
        Snooping."
    ::= { cisMIBGroups 24 }

cisSourceOnlyAgeTimerInSecGroup OBJECT-GROUP
    OBJECTS         {
                        cisSourceOnlyLearningEnabled,
                        cisSourceOnlyEntryAgingTime
                    }
    STATUS          current
    DESCRIPTION
        "A collection of object(s) providing configuration and
        information of Source Only learning control and 
        age timer in seconds."
    ::= { cisMIBGroups 25 }

END